10.0 mm Plain Tight TIR
|LEDs & Performances||Eff.||FWHM||Cd/lm||Spot||Cross-section||Files|
|Lumileds Luxeon Rebel Cool White||89.6%||18.4||6.5||10412_Rebel_White_250408.ies|
|Lumileds Luxeon Rebel Neutral White||84.0%||17.8||7.9||10412_Rebel_Neutral_White_250408.ies|
|Lumileds Luxeon Rebel Warm White||87.6%||16.5||9.3||10412_Rebel_Warm_White_250408.ies|
|Cree XP-E XLamp® White||91.8%||16.5||9.3||10412_cree_xpe_white_250408.ies|
|Cree XP-G XLamp® White||91.0%||24||4.6||10412_cree_xpg_white_250408.ies|
|Osram SSL 80 degree Oslon Ultra White||89.2%||18.8||8.0||10412_Oslon_wht_250408.ldt|
|Nichia NCSL 119-H3 Top Emitting Warm White||84.6%||16.2||7.5||10412_Nichia_119_Warm_White_250408.ies|
|SSC Z5 Cool White||86.5%||16.1||11.3||10412_Seoul_Z5_white_250408.ies|
|Everlight Shuen Warm White||87.5%||21.8||4.8||10412_Shuen_wwht_250408.ies|
|Everlight Shuen Cool White||86.2%||20.9||4.6||10412_Shuen_cwht_250408.ies|
|Lumileds C Luxeon Cool White||85.9%||14.2||12.6||10412_Luxeon C_white_250408.ies|
|Lumileds ES Luxeon Rebel Cool White||88.3%||23.5||4.6||10412_Luxeon_Rebel_ES_cool_white_040311.ies|
|Cree XP-C White||91.7%||10.7||21.0||10412_Cree_XP-C_white_220611.ies|
|Osram SSL 150 degree Oslon Neutral White||90.0%||15.1||12.0||10412_Oslon 150_neutral white_260711.ies|
|SSC Z5P Seoul SC pure white||87.9%||18.5||7.9||10412_Z5P_purewhite_290911.ies|
|Samsung samsung3535 White||92.9%||22.5||5.8||10412_Samsung 3535_cool white_181011.ies|
|Cree XB-D XLamp® Warm White||89.7%||19.5||7.1||10412_CREE_XBD_200212.ies|
|Cree XT-E XLamp® Cool White||89.0%||23.25||5.0||10412_CREE XTE_200212.ies|
|SSC Z5M White||%||21.9||5.7||10412_SeoulZ5M_warm white_250612.ies|
|Lumileds R Luxeon||88.3%||23.5||4.6||10412_Luxeon_R_cool_white_040311.ies|
|Cree XPG-Gen2 XLamp® Warm White||%||23.0||5.8||10412_XPG-Gen2_170712.ies|
|Nichia 219 Warm White||%||22.6||4.7||10mm_10412_Nichia 219_120213.ies|
|LG 3535 Cool White||%||23||5.5||10412_LEMWA33X70GW00_Cold white_130412.ies|
|Lumileds T Luxeon||88.3%||23.4||4.6||10412_Luxeon_T_140513.ies|
|Cree XPE-2 XLamp® Cool White||%||16.2||11.2||10412 Plain Tight_Cree XPE2_23052013.ies|
Carclo Optics endeavours to continuously improve and renew its products; for this reason the technical data and contents of this catalogue may undergo variations without prior notice. For correct and up to date information, Carclo suggest using the Opticselect tool on our website http://www.carclo-optics.com.
Copyright © Carclo 2010
General Instruction - Optics & Holders
Disclaimer - Optics & Holders
Please note that flow lines, weld lines, surface scratches and small black or white inclusions within the lenses are acceptable if the optical performance of the lens is within the specification described below:
For optics that have FWHMs of 20 degrees or less, the general tolerance is +/-2 degrees OR the tolerances stated below - whichever is the greater.
For all optics except Rippled and Frosted;
For all Rippled and Frosted Optics;
For all Optics;
The yellowing / browning of polycarbonate lenses and holders can occur due to the natural ageing process and exposure to heat and UV and as such is not covered by Carclo’s warranty.
General Instruction - Taped Holders
Bond strength is dependent upon the amount of adhesive-to-surface contact developed. Firm application pressure and moderate heat, from 100°F (38°C) to 130°F (54°C), will assist the adhesive in developing intimate contact with the bonding surface.
Ideal tape application temperature range is 70°F to 100°F (21°C to 38°C). Initial tape application to surfaces at temperatures below 50°F (10°C) is not recommended because the adhesive becomes too firm to adhere readily. However, once properly applied, low temperature holding is generally satisfactory.
During assembly the optic when placed on the PCB should be firmly held for 1-5 seconds to ensure the best possible bond. The tape will reach its final strength in 72 hours, dependent on the material and ambient conditions.
We request that the customer ensures (and fully tests) the suitability and sufficiency of the bond in his product. For example, mechanical stress, vibration and holes on the surface of the circuit board can weaken the strength of the tape.
Disclaimer - Taped Holders
Shelf Life - There is 1 year expected shelf life from the date of purchase direct from Carclo.
All Carclo lenses supplied with tape use the same high strength double-coated tape (unless otherwise mentioned in the datasheet). This tape is specifically selected for this application.
These tapes generally work well together with PCBs and LEDs on the market. The customer must take the necessary measures to ensure complete compatibility with their particular application, product, PCB, LED and/or other components.
Testing and verifying of the adhesives and their combinations is the responsibility of the customer.
The customer is solely responsible for evaluating the application of double sided tape to Carclo Holders and the adhesion of double sided tape holders to determine whether such double-sided tape is fit for a particular purpose and suitable for the users method of application. The selection of double-sided tape in the adhesion of double sided tape holders is not covered by Carclo’s warranty.
Carclo cannot take responsibility for the results obtained by others whose methods we cannot control. It is always the customer’s responsibility to determine the adhesive’s suitability for their product and to take precautions for protection of property and persons against any hazards that may be involved in the handling and use of adhesives. Carclo disclaims all warranties, including warranties of merchantability or suitability for a particular purpose, arising from use of any adhesive product. Carclo disclaims any liability for consequential or incidental damages of any kind, including lost profits.
All rights reserved. No part of this publication may be copied, reproduced in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, illustrations not to be removed, without our prior permission. Carclo Optics reserves the right to make changes at any time in order to supply the best products possible.